LAB Cementum (Concrete look)



LAB Cementum Colours (DIY Concrete Look)

LAB Cementum (concrete look) is an easy to use system for walls that easily creates a concrete effect. Easy to use and extremely wear-resistant. Mixable in an approximation of all unique LAB COLOURS and on request in almost any other colour from 50 litres. You apply this system in multiple layers. After finishing with 2 layers of LAB Cementum Coating Transparent, the surface becomes completely waterproof, making LAB Cementum also suitable for bathrooms (including wet cells, except for the floor), toilets, kitchens and other intensively loaded walls. Of course, a decorative wall in, for example, a living room or bedroom is also possible. In that case, a finish with LAB Cementum Coating Transparent is not required, but it is desirable for intensively loaded walls or walls that have to meet high demands on cleanability.

Order LAB Cementum processing packages? View the complete LAB Cementum Walls system processing package here .

✓ LAB Cementum is an easy to use system that easily creates a concrete effect and is easy to use.
✓ LAB Cementum can be used as a decorative finish but is also suitable for bathrooms (including wet rooms), toilets and kitchens.
✓ LAB Cementum can be mixed in an approximation of all unique LAB COLOURS and in almost any other colour on request.
✓ LAB Cementum consists of, among other things, resin-reinforced mineral raw materials coloured with LAB pigments.
✓ LAB Cementum contains no/very few solvents. Meets the Arbo for professional use indoors. If you have any questions, please contact us.

LAB Cementum Walls

LAB Cementum Walls is an easy to use system that can be used to create a concrete effect on walls. It is very easy to apply. The LAB Cementum Walls system consists of 3 different products, namely: LAB Cementum Wall Primer, LAB Cementum Wall and LAB Cementum Coating Transparent (optional). LAB Cementum Walls is available in sets of 5 m², 10 m² and 25 m² excl . LAB Cementum Coating Transparent.

Applicable to walls of chipboard, mdf, plasterboard, plaster blocks, ytong blocks, lime sand brick, new stucco, plasterwork, painted walls and tiles which are finished with the complete LAB Cementum Walls system. The surface must always be load-bearing, dry, dust and grease-free and may not contain cement skin, glue and (silicone) sealant residues.

Please note! Each surface requires a different pretreatment. A good pretreatment prevents most problems. By pretreating the surface in the right way, a good bond with the product can be obtained. If in doubt, always perform an adhesion test first and assess it after hardening. View the product information sheet to see which pretreatment applies to your wall.

LAB Cementum Colours (DIY Concrete Look)

Step 1: LAB Cementum Wall Primer

Apply LAB Cementum Wall Primer with wall paint roller GREEN PROF (10 cm and 18 cm) and use a flat synthetic brush PROF (size 40) for the corners. Stir well before use. LAB Cementum Wall Primer is an adhesion primer and contains some structure, which ensures good adhesion with LAB Cementum Wall. Apply LAB Cementum Wall Primer in 1 to 2 opaque layers. Process between 5-25 degrees. Dust dry after approx. 2 hours and can be painted over after approx. 4 hours (depending on temperature and humidity).

Step 2: LAB Cementum Wall

Apply LAB Cementum Wall with wall paint roller GREEN PROF (10 cm and 18 cm) and use a flat synthetic brush PROF (size 40) for the corners. Before use, mix mechanically with a drill and a paint mixer (metal with plastic - Ø55 mm) until a homogeneous mass is obtained. LAB Cementum Wall is a decorative concrete stucco and consists, among other things, of mineral raw materials reinforced with resin and coloured with LAB pigments. Apply LAB Cementum Wall in a layer thickness of approx. 0.2-0.5 mm. Then finish the walls with Spaan PROF as soon as the LAB Cementum Wall starts to dry. This creates the first layer of the desired concrete effect. Then check the surface for any imperfections. Remove these with a knife, for example; sanding is not necessary. Apply LAB Cementum Wall in 2 opaque layers. For more concrete effect, a thin layer can be applied, making colour and structure variations visible compared to the first layer. A thin layer dries faster and is only possible if the first layer has already achieved sufficient layer thickness. Process between 15-25 degrees. Dust dry after approx. 2 hours and can be painted over after 4-8 hours (depending on temperature and humidity). If desired, LAB Cementum Coating can be applied after at least 24 hours.

Step 3: LAB Cementum Coating Transparent (optional)

Apply LAB Cementum Coating Transparent with coating and paint roller WHITE PROF (MICROFIBER) (10 cm and 18 cm) and use a flat synthetic brush PROF (size 40) for the corners. Before use, mechanically mix the two components with a drill and a paint mixer (metal with plastic - Ø55 mm) until a homogeneous mass is formed. After mixing, process within 2 hours. LAB Cementum Coating Transparent can be used as an additional finishing and protective layer for LAB Cementum Walls and LAB Cementum Floors. This makes the walls and floors very easy to clean and completely waterproof. Apply LAB Cementum Coating Transparent in at least 2 opaque layers. For floors subject to intensive use, we recommend a 3rd or 4th layer. The LAB Cementum Walls sets of 5 m² and 10 m² are excl. LAB Cementum Coating Transparent. LAB Cementum Coating Transparent is available in 1 litre and 2.5 litre cans. Consumption per litre is approx. 12 m². LAB Cementum Coating Transparent is available in the gloss levels Matt and Satin. Process between 10-25 degrees. Dust dry after approx. 2 hours, can be painted over after approx. 5 hours, lightly loaded after approx. 14 hours, fully loaded after 7 days and fully cured after 28 days (depending on temperature and humidity).

We advise you to read the relevant product information sheet before using any of the above products. More information and/or questions? Feel free to send an e-mail to support@vestingh.nl or contact us by phone.

Maintenance LAB Cementum Walls

  • For cleaning and sanitizing LAB Cementum Walls, preferably use LAB ECO Cleaner. Do not use aggressive cleaning agents such as ammonia, all-purpose cleaner or bleach. These products will damage the coating. When no coating is used, the walls can only be cleaned with a soft, damp cloth and lukewarm water.
  • Remove spilled liquids and other contamination from LAB Cementum Walls as soon as possible to prevent penetration. Only clean with a damp cloth if necessary.
LAB Cementum Colours (DIY Concrete Look)

LAB Cementum Colours (DIY Concrete Look)

    Order LAB Cementum (concrete look)? Click on the desired LAB COLOUR or enter the name of the LAB COLOUR in the search bar and check LAB Cementum Walls.

    Order LAB Cementum processing packages? View the complete LAB Cementum Walls system processing package here .

    Want to see more from LAB PAINT?

    Please note: screen colours may differ from the actual paint colours depending on screen settings. The incidence of light can also largely determine a colour on the wall and the atmosphere in the room. The colours on the colour samples are indicative and an approximation. The final colour depends on the processor, the layer thickness, the processing temperature and the humidity.